Changes

[[CDB|Main]] / [[:Category:Guides|Guides]] / '''{{PAGENAMEguide}}'''

A lot ==The Art of people complain about this type of bridge, but until we have proper bridges (and maybe boats) they are our only way to connect two landmasses.Making Land Bridges==

===Find best place===The best place for a landbridge is the shortest distance between 2 shoresA lot of people complain about this type of bridge, but it is better being in a straight line than going diagonaluntil we have proper [[bridges]] they are our only way to connect two landmasses.

===Find the Best Place===The best place for a land bridge is the shortest distance between 2 shores, but it is better to be building in a straight line rather than going diagonal. ===Water Depthdepth===Depth of water is a big factor as dirt "flows" when a slope get gets to 40 (4 meters), what i mean by "Flow" is meaning that the dirt will slide down the slope until it gets to a lesser slope.

As part of planning a LandBridgeland bridge, it maybe may be a good idea to estimate the number of cartloads required. This should be easy, all you have to do is work out how many much dirt you need to drop on each corner of the tiles a tile to raise it above water level. '''Note don''': Don't take into account the dirt flow.

===Example: Vires LandBridge=How depth affects the dirt flow====So for the Vires LandBridge, the depth was, on average, 70 Any dirt (less than 2 cartloads), and the bridge was/is 30 dropped will flow to adjacent tiles longkeeping a maximum slope of 40...

Next decide The problem is that the dirt flows out in all eight directions so...<pre>A---B---C---D---E| | | | |F---G---H---I---J| | | | |K---L---M---N---O| | | | |P---Q---R---S---T| | | | |U---V---X---Y---Y</pre>So if this area was flat and you dropped 40 dirt on corner M, it would just pile up, but if you now dropped 9 more there then it would raise corners G,H,I,L,N,Q,R,S and M up by one dirt. So to get corner M 80 dirt higher than it started, you want need to do a one tile or two tile wide LandBridgeget corners G,H,I,L,N,Q,R, a one tile wide LandBridge will be affected by S up 40 dirt floweach, where as a two tile one is not (if done correctly)so you would have had to drop 400 dirt.

So to raise corner M up 120 dirt, then you need to get all corners 40 up, + 40 more for the middle ones + 40 for M = 25 * 40 + 9 * 40 + 40 = 1400 dirt (35 cart loads). ===Example: Vires Land Bridge===So for the Vires land bridge, the depth was, on average, 70 dirt (less than 2 cartloads), and the bridge was/is 30 tiles long.  Next decide if you want to do a one tile or two tile wide land bridge. A one tile wide land bridge will be affected by dirt flow, where as a two tile one is not (if done correctly). So for the Vires LandBridgeland bridge...

So looking at that, a 2 tile wide LandBridge land bridge would take a fraction more than a one tile wide one upto up to an average depth of 70 dirt. So if the deepest part is over 100 deep, then i I would recommend a 2 tile wide one. The decision for the Vires land bridge was for a 2 tile wide one as it looks a lot better than a single tile (also some tiles were a lot deeper than 70).

The decision for the View LandBridge was for It's also easier to slip off a 2 one tile wide one as it looks bridge, so a lot better than a single 2 tile (also some tiles were a lot deeper than 70)bridge is more convenient to use.

Enough of deciding what type of LandBridge land bridge to go for... Here is how to do one

<ol><li>Single Tile width (wasting dirt!)</li>

Drop dirt on each corner off the deep end of the LandBridge land bridge to bring each corner upto up to the same height.

<li>Single Tile width (No so much wasted dirt!)Width</li>

<li>Double width Single Tile Width</li> Plan... <pre> a b e +---+---+---+land| 1 | 2 | 3 |water +---+---+---+ c d f</pre><ul><li>Tile 1 (flat) already is flattened and in all 4 sides has 0 dirt slope.</li><li>Tile 2 (flat) both sides already are in water with 41 dirt slope.</li><li>Tile 3 (No wasted 30 dirt!slope to water).</li></ul>How to flatten tile 3. <ul><li>1. Drop 16 dirt on tile 1 corner a.</li><li>2. Drop 16 dirt on tile 1 corner c.</li><li>3. Flatten tile 1.</li><li>4. Flatten tile 2.</li><li>5. Start flattening tile 3 until the tile's corners e and f will be in water level or tile 2 slope will be 20 dirt.</li><li>6 . Flatten tile 1.</li></ul> Start everything from step 1 until all 3 tiles are flat. Process explanation. So where is the secret? Very simple, first you raise tile 1, then with flattening help you move dirt to tile 2 and then to tile 3. This way of land bridge building is good when you don't have enough space to build a 2 tiles wide bridge or you don't want to spend the rest of your Wurm life by digging dirt for a 2 tiles wide bridge. <li>Double width</li>

EvaluationElevation...

\ C

<li>For best results try to keep the whole LandBridge land bridge 3 dirt above the water level, pack it and pave it (then you should not get any water showing through).</li></ul> ==Tips==<ul><li>If you can't flatten a tile because you don't have enough skill, drop dirt on the lowest point<li><li>When flattening, don't stand on the highest point as you may get "Ouch that hurt!" (multiple times)</li>

[[Category<span style="display:Guides]][[Category:Babel/L]]none;">--[[User:Tich|Tich]] 02:27, 22 January 2007 (CST)</span>